Haier Refrigerator DD300RW User Manual

All refrigerating dual-drawers refrigerator  
Models:  
DD300RWWhite exterior)  
DD350RBBlack exterior)  
DD400R* Stainless steel Door)  
DD450R* Wood door plate)  
1
 
SAFETY PRECAUTIONS  
Read all of the instructions before using this appliance.  
When using this appliance, always exercise basic safety  
precautions, including the following:  
1) Use this appliance only for its intended purpose as described in this use  
and care guide.  
2) This refrigerator must be properly installed in accordance with the  
installation instructions before it is used. See grounding instructions in  
the installation section.  
3) Never unplug your refrigerator by pulling on the power cord. Always grasp  
the plug firmly and pull straight out from the outlet.  
4) Repair or replace immediately, all electric service cords that have  
become frayed or otherwise damaged. Do not use a cord that shows  
cracks or abrasion damage along its length, the plug or the connector  
end.  
5) Unplug your refrigerator before cleaning or before making any repairs.  
Note: If for any reason this product requires service, we strongly  
recommend that a certified technician performs the service.  
6) Do not use any electrical device or any sharp instrument in  
defrosting your refrigerator.  
7) If your old refrigerator is not being used, we recommend that you remove  
the doors and leave the shelves in place. This will reduce the possibility  
of danger to children.  
8) After your refrigerator is in operation, do not touch the cold surfaces in the  
refrigerator compartment, particularly when hands are damp or wet. Skin  
may adhere to these extremely cold surfaces.  
9) Do not refreeze foods, which have been thawed completely. The United  
States Department of Agriculture in Home and Garden Bulletin No. 69  
reads: “⋯ You may safely refreeze frozen foods that have thawed if  
they still contain ice crystals or if they are still cold-below 40˚F.  
“⋯ Thawed ground meats, poultry, or fish that have any off-odor or  
off-color should not be refrozen and should not be eaten. Thawed ice  
cream should be discarded. If the odor or color of any food is poor or  
questionable, discard it. The food may be dangerous to eat.”  
“⋯ Even partial thawing and re-freezing reduce the eating quality of  
foods, particularly fruits, vegetables, and prepared foods. The eating  
quality of red meats is affected less than that of many other foods. Use  
refrozen foods as soon as possible, to save as much of its eating quality  
as you can.”  
10) This refrigerator should be recessed or built-in an enclosed cabinet. It is not  
designed for freestanding installation only.  
11) Do not operate your refrigerator in the presence of explosive fumes.  
3
 
SAVE THESE INSTRUCTIONS  
For Future Use  
DANGER  
Risk of child entrapment. Before you throw away your old  
refrigerator or refrigerator, take off the door. Leave the shelves in  
place so that children may not easily climb inside.  
Thank you for using our Haier  
product. This easy-to-use manual  
will guide you in getting the best  
use of your refrigerator.  
Remember to record the model and  
serial number. They are on a label  
in back of the refrigerator.  
Model number  
Serial number  
Date of purchase  
Staple your receipt to your manual. You will need it to obtain warranty  
service.  
TABLE OF CONTENTS  
4
 
Structural drawing  
Dimensions drawing  
5
 
Installing instruction  
This refrigerator is a kind of build-in product, before you use it  
this product must be installed.  
Preparation before installing:  
First,clean product’s surface with soft cloth,remove all protective coating and belt covering the  
product.Don’t use abrasive cleaning cleaners.  
1.Pull the upper drawer open,Refer to the illustrations below,put both dividers of shelf on  
same side,lift the crisper up off the upper drawer.  
2. Lift up both sides of the shelf off the bin cradle with two hands together.  
3. Rotate the shelf of upper drawer  
6
 
4.Take the upper shelf out of the upper compartment  
Note: After these four steps finished ,please close the upper drawer to avoid damage to your  
body by sliding out of drawers of following installation.  
Installation:  
This refrigerator is a kind of build-in product, before you use it  
this product must be installed.  
First step:Take off  
part“1” (holes cover) of Structural drawing with upwards  
strength ,refer to illustrations below:  
7
 
Sencond step:  
Take the anti-tip bracket and screws from the accessory bag. Tighten the anti-tip  
bracket on the top of the product with screws as following the illustration  
Note:Please install just as following illustrations about holes,If you choose wrong hole,it will  
do damage to the top of your product and screws.Besides,you should adjust the position of  
bracket base on the height of unit in advanceso that we could save operation of taking out  
the unit of counter again to choose position of bracket in next step.  
Anti-tip Bracket  
Screw  
Third step: Put the unit inside of counter.Pull upper drawer open and attach the anti-tip  
bracket to counter by screw. You can adjust the feet on the corners of unit (Part 7 in Structural  
drawing)  
8
 
Removable interior parts:  
Crisper  
One cripser with cover in upper drawer,user can adjust the position of crisper depending  
on needs of storage.  
Purpose: Convenient for separate storage of fresh vegetable or fruits.It can stop from  
Risk of Odour. You can take crisper out when not needed.  
Adjustable shelf.  
There are an adjustable shelf in each drawer.User can adjust them to be suitable for  
different food storage . You can take it out when not needed.  
Note: Keep it in safe place if taken out,especially keep it from children to avoid damage to  
them and itself.  
Adjust of shelf of upper compartment  
Separate the compartment to left and right or vice versa.  
Rotate the shelf from  
the right side to the left  
side or vice versa  
The rotation operation  
finished  
Separate the compartment to front and back or vice versa  
9
 
Push  
the  
plastic  
according to the arrow  
and move along the  
direction of the steel bar  
Move the shelf from A to  
B
The upper compartment is seperated to left and right parts by middle shelf fastened to bin  
cradle of upper compartment.Those two dividers of shelf can be adjusted left and  
right,also back and front.For left and right adjust:you can rotate directly. For back and  
front: you should push the “push” button in middle connector and move it back to front . If  
you want to clean your refrigerator,you can remove the shelf following step of  
Preparation before installing  
Purpose:People can separate the upper compartment with divider according to personal  
needs,can keep foods fixed to avoid falling down when drawers and being opend and  
closed.  
Adjust the shelf of lower compartment,referring to illustrations:  
10  
 
The shelf of lower compartment is fixed between the embossments of front and back wall  
of drawer.You can choose different embossments to divede into different spaces in  
drawer.  
Purpose: People can separate the lower compartment with divider according to personal  
needs,  
Dimensions of drawers  
Upper drawer  
It can load the 2 litter bottle with height of 12 inch,so it can stock all foods or beverage  
whose height is less than 12 inch.  
Lower drawer  
Lower drawer is seperated by step.Foods or beverage whose height is less than 12 inch can  
be kept in the space without step.Pop cans can be kept in space with step.  
How to use this product  
Important notes before connect the power supply:  
CAUTION: DON'T USE EXTENSION CORDS.  
Actual power supply should keep in accord with marks in rating  
plate(115V/60HZ).Rating plate is on back of unit.  
Power socket should equiped with fuse of 10A.Keep the refrigerator still for half or one  
hour before connnecting to power socket which has been grounded.  
Connect the power supply:  
Unit is inspected and set to be 38before leaving the factory.When connected with the  
power supply,Unit will work normally.  
11  
 
Interior LED bulb:  
LED bulb is located on top of interior liner in each upper and lower compartment.It is  
controlled by approaching switch: when drawer is open,it’s on,when drawer is close,it’s off.  
Caution: there are magnet who fix the approaching switch on left side of interior upper  
drawer and bottom of lower drawer door.Don’t remove them when unit are working normally.  
Temperature setting:  
If you wan to change temperature,press “SET” for three seconds,temperature figure will flash  
in control panel,then you can adjust the figure and press “SET” to confirm after you complete  
your operation.  
If you want to reduce the temperature,press the button of ∨  
If you want to raise the temperature,press the button of ∧  
For example:if you want get 450F, just press “SET” button momently,when “tick”,the figure of  
temperature will flash,now you can adjust the temperature,after adjustment,press “SET” to  
confirm,then the figure of temperature will flash again.After 5 seconds,it will display the actual  
temperature of unit. Then the figure of temperature will keep changing until reach adjusted  
temperature,and the display panel will show the changing temperature also.  
Temperature range is : 3447 17℃).  
Thermoregulation guard  
Design of thermoregulation guard lock is to avoid children’s changing unconsciously.  
Thermoregulation guard unlock: press and hold “SET” for 3 seconds.when “tick”,it means  
unlock signal,the temperature figure flashes,you can adjust now.After adjustment,press “SET”  
to confirm and start thermoregulation guard clock. Now you can’t adjust the temperature by  
pressing “∧∨”.  
Degree Centigrade and Fahrenheit conversion:  
Press and hold“select”for 3 seconds, temperature display will change from Fahrenheit to be  
12  
 
Centigrade degree,buzzer will ring once. Press and hold “select” for 3 seconds,it will change  
form Centigrade to be Fahrenheit, buzzer will ring once again.  
Power switch  
Display panel has power button”Power”,If you want to stop unit working for short time or to  
restart,press and hold“power” for 3 seconds to open and close.  
Notes:If you want to stop unit working for long time,please shut off power supply,take off plug  
of socket, cut off the fuser,clean RF,and remove door of unit to get rid of Odour  
Sabbath mode  
Note: This mode is available for the observance of certain religious holidays.  
Press and hold ” and ” at the same time for 3 seconds, buzzer will ring once,  
display panel will flash for 3 times and close.This indicates that the unit has entered Sabbath  
mode.In this mode,normal cooling operations still take place(compressor,magnetic  
valve,fan,heater strip),but all luminous equipment including display panel,LED bulb will shut  
off no matter door is opening or closing.  
Press and hold ” and ” at the same time for 3 seconds,after figure of display panels  
flashs for 3 times,you can exit from Sabbath mode.  
Sound alarm system  
Sound alarm system can keep temperature from exceeding so much  
If the door of unit is kept open for long time and affect temperature so much,the system will  
give an alarm,if you want to close it,press “SET” button.  
When interior temperature of  
unit is too hot or cold,product will give an  
alarm.Temperature display will change and flash.It will keep flashing until the cause is  
removed.If you want to close alarm system,press “SET”button.  
Notes: When display error appears,alarm system will take effect,you can shut off the  
power supply for 10 minutes if not aware of cause. Restart it again.If problems remain,please  
contact with nearest customer sevice center.  
Auto Defrost  
Unit can defrost automatically: the water of back wall will drain into water tank and be  
evaporated by the calorie of condensator.Please check if water can drain into the tank  
automatically.  
13  
 
Cleaning:  
Before cleaning,shut off the power of unit.Take off the plug of socket and remove fuser.  
Clean interior surfaces and accessories and outer frame with cold water and a little baking  
soda.  
Don’t clean with steam to avoid damage to product.  
Don’t use abrasive , acidic and chemistical cleanser,Recommend to use neutre cleanser  
Keep cleanser from immerging into elcetrical device.  
Clean and dry all accessories.  
Clean drain hole which is between comparments of unit with small and  
soft cleaner such as cotton swab.  
TroubleShooting  
Refrigerator does not operate:  
z
z
Check if refrigerator is plugged in.  
Check if there is power in the AC outlet,by checking the circuit breaker.  
Refrigerator too warm:  
z
z
z
z
z
Frequent door openings.  
Allow time for recently added beverage to reach desired temperature.  
Check gakets for proper seal.  
Clean condenser coils.  
Adjust temperature control to colder setting.  
Refrigerator runs too frequently:  
z
z
This may be normal to maintain constant temperature during high temperature and  
humid days.  
Doors may have been opened frenquently or for an extended period of time.  
14  
 
z
z
z
Clean condenser coils.  
Check gasket for proper seal.  
Check to see if doors are completely closed.  
Moisture build up on interior or exterior of the refrigerator:  
z
z
z
This is normal during high humidity periods.  
Prolong or frequent door openings.  
Check door gaskets for proper seal.  
Refrigerator door does not shut properly:  
z
z
Level the refrigerator.  
Check for blockages e.g. beverage bottles,slide orbit,signal wire under the upper drawer  
and the switch under the door plate of the lower drawer.  
appliance for a period of 12months. This  
Limited Warranty  
includes all parts except finish ,and trim.  
The components of the sealed system e.g.  
hermetic compressor,condenser and  
evaporator from manuafacturing defects for  
a period of 5 years from the date of  
purchase.  
What is covered and for how long?  
This warranty covers all defects in  
workmanship or materials for a period of :  
12 months labor  
Any damages to such components caused  
by mechanical abuse or improper handling  
or shipping will not be covered.  
12 months parts  
5 years sealed system  
The warranty commences on the date the  
item was purchased and the original  
purchase receipt must be presented to the  
authorized service center before warranty  
repairs are rendered.  
What will be done?  
We will repair or replace,at our discretion  
any mechanical or electrical part which  
proves to be defective in normal usage  
during the warranty period so specified.  
There will be no charge to the purchaser for  
parts and labor on any covered items during  
the initial 12 month period.Beyond this  
period only parts are covered in the  
EXCEPTIONS:Commercial or Rental Use  
warranty  
90 days labor(carry-in only)  
90 days parts  
No other warranty applies  
remaining warranty. Labor is not provided  
and must be paid by the customer.  
What is covered.  
Contact your nearest authorized service  
center. For the name of the nearest serive  
center please call 1-877-337-3639  
The mechanical and electrical parts,which  
serve as a functional ,purpose of this  
15  
 
THIS WARRANTY COVERS APPLIANCES  
WITHIN THE CONTINENTAL UNITED  
STATES, PUERTO RICO AND CANADA.  
IT DOES NOT COVER THE FOLLOWING:  
Damages from improper installion.  
Damages in shipping.  
PURPOSE  
The remedy provided in this warranty is  
exclusive and is granted in lieu of all other  
remedies.  
This warranty does not cover incidental or  
consequential damages, so the above  
limitations may not apply to you. Some  
States do not allow limitations on how long  
an implied warranty lasts, so the above  
limitations may not apply to you.  
This warranty gives you specific legal rights,  
and you may have other rights, which vary,  
from state to state.  
Defects other than manufacturing.  
Damage from misuse, abuse, accident,  
maintenance or incorrect current or voltage.  
Damage from other than household use.  
Damage from service by other than an  
authorized dealer or service center.  
Decorative trims or replaceable light bulbs.  
Transprotation and shipping.  
Haier America  
Labor(after the initial 12 months).  
THIS LIMITED WARRANTY IS GIVEN IN  
LIEU OF ALL OTHER WARRANTIES,  
EXPRESSED OR, INCLUDING THE  
WARRANTY OF MERCHANTABILITY  
AND FINESS FOR A PARTICULAR  
New York, NY 10018  
IMPORTANT  
Do Not Return This Product To The Store  
If you have a problem with this product, please contact the “Haier Customer  
Satisfaction Center”at 1-877-337-3639.  
DATED PROOF OF PURCHASE REQUIRED ROR WARRANTY SERVICE  
16  
 
Made in China  
Haier America  
New York,NY 10018  
Printed in China  
17  
 

Grizzly Grinder T10010 User Manual
GTO Safety Gate RB909 User Manual
Hasbro Door PUB 0804 User Manual
Hasbro Games 05949 User Manual
Honeywell Air Cleaner HHT 080 User Manual
Huawei Cell Phone U8815N User Manual
Hunter Fan Fan Type 7 Models User Manual
Husqvarna Chainsaw 50 Rancher User Manual
iHome Speaker System IHM60EN User Manual
Ikelite Digital Camera W 120 User Manual