GE Monogram Refrigerator B420DR User Manual

ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side Refrigerator  
with Dispenser and Water Filter  
Dimensions and Clearances (in inches)  
* Shipping height.  
41"  
The Installation Space  
25-3/8  
Case Width  
The refrigerator  
can be adjusted to  
fit into a cutout that  
is 83-1/2" min. to  
84-1/2" max. height  
Note that the top  
case trim at the  
36" Models 12"  
42" Models 18"  
48" Models 20"  
*Finished Width  
*84" From  
Floor to  
Top Frame  
*83-1/2"  
at  
Rear  
6"  
Electrical  
Area  
front is 1/2" higher  
and will overlap  
upper cabinetry or  
soffit. Use leveling  
legs and wheels for  
a maximum 1" height  
adjustment.  
84-1/2" max  
83-1/2" min  
Finished  
5"  
75" From Floor  
to Bottom  
of Electrical  
Area  
Opening  
42"  
24"  
26-7/8"  
including  
handle  
Frame to Frame  
5"  
5"  
Water Supply  
3-1/2"  
Door Swing Clearances  
3-1/2"  
The installation must allow for clearances to adjacent walls or  
cabinets. These refrigerators are equipped with a 2-position  
door stop. The factory-set 130° door swing can be adjusted to  
90° if clearance to adjacent cabinets or walls is restricted.  
Space is the first consideration when planning the installation.  
The cutout depth must be 24"  
The refrigerator will project forward, slightly beyond adjacent  
cabinetry, depending on your installation.  
90° Door Swing  
130° Door Swing  
13"  
19"  
23-7/8"  
Behind  
Frame  
The cutout depth beneath a soffit  
When installed beneath a soffit, the soffit cannot exceed the  
24" installation depth shown. The top case trim overlaps the  
bottom of the soffit.  
26-5/8  
Electrical  
A 115V, 60Hz., 15 or 20 amp power supply is required. An  
individual properly grounded branch circuit or circuit breaker  
is recommended. Install a properly grounded 3-prong electrical  
receptacle recessed into the back wall. Electrical must be  
located on rear wall as shown.  
4" Min.  
to Wall  
Allow minimum clearances for freezer door and fresh food  
door for a full 130° door swing and to allow for pan removal.  
• 4" minimum clearance is required when door swing is  
adjusted to 90°. If the 90° door stop position is used, pan  
access is maintained, but pan removal is restricted.  
Note: GFI (ground fault interrupter) is not recommended.  
Water Line  
All models are equipped with an automatic icemaker. The  
water line can enter the opening through the floor or back  
wall. Route 1/4" O.D. copper tubing or GE QuickConnect  
kit between the cold water line and the water connection  
location. The copper tubing should be long enough to extend  
to the front of the refrigerator. The installation of an easily  
accessible shut-off valve in the water line is required.  
• See door swing illustrations to determine interaction with  
adjacent cabinets or countertops.  
Installation Information: Before installing, consult  
installation instructions packed with product, or online at  
Monogram.com, for current dimensional data.  
For answers to your Monogram,® gE Profileor  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
gE® appliance questions, visit our website at  
Listed by  
Underwriters  
Laboratories  
gEAppliances.com or call  
gE Answer Center® service, 800.626.2000.  
Specification Revised 3/08  
110171  
 
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side Refrigerator  
with Dispenser and Water Filter  
3/4" Overlay Panel Dimensions  
Raised Overlay Panel Design  
On Dispenser Models  
For a more custom appearance, overlay  
panels may be installed on trimmed  
models. the overlay panel must be  
secured to a 1/4"-thick backer panel  
which slides into the trim. A spacer  
panel 0.10" thick must be placed  
When a raised panel design is to be used, a custom wide middle rail  
Door  
3/4"  
Overlay  
Panel  
is required to accept the dispenser trim.  
the middle rail must be wide enough to allow for the dispenser  
trim to overlap the opening.  
the middle rail must be 1.100" total thickness to accept the  
dispenser trim.  
between the overlay and backer panels.  
1/4" Backer Panel  
3/4" Overlay Panel  
.250" + .10" + .750" =  
1.100" total Panel thickness  
1/4"  
Backer  
Panel  
.10"  
Spacer  
Overlay Panel  
Spacer Panel  
Backer Panel  
Center each panel over the other.  
Assemble the panels with glue  
and screws. Screws must be  
Dispenser  
Trim  
Wide  
Middle  
Rail is  
16-3/4"  
Required  
countersunk into the backer panel.  
NOTE: Left-to-right offset is  
not always equal to  
top-to-bottom offset.  
10-5/8"  
Side View  
A
42" Side-by-Side (in inches)  
Grille Panel  
B
C
A
B
C
D
E
1/4" Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16  
.10" Spacer Panel 39 8-5/8 67 13-1/4 23-1/4  
F
Dispenser  
Cutout  
3/4" Spacer Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16  
Dispenser Cutout  
Dispenser Cutout Position (in inches)  
G
F
G
42" Models  
17-15/16  
3-1/4  
15-3/  
Freezer  
Panel  
Fresh  
Food  
D
9-5/8"  
As an EnErgy StAr®  
*Cut the dispenser opening after the backer, spacer and overlay  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
Listed by  
Underwriters  
Laboratories  
panels have been assembled.  
Important Note: Maximum total panel weight:  
• Fresh food door panel – 75 lbs.  
• Freezer door panel – 53 lbs.  
For answers to your Monogram,® gE Profileor  
gE® appliance questions, visit our website at  
gEAppliances.com or call  
• grille panel – 18 lbs.  
gE Answer Center® service, 800.626.2000.  
Specification Revised 3/08  
110171  
 
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side Refrigerator  
with Dispenser and Water Filter  
1/4" Framed Panel Dimensions  
Dispenser Models  
If you choose to install framed panels,  
they must be cut to the dimensions  
shown. the panels will slide into the  
frame on the door and grille.  
these refrigerators are supplied with two dispenser trims, one for  
5/16"  
Trim  
framed panels and one for overlay panels.  
Door  
Revea  
1/4" Framed Panel  
the framed panel must be 1/4" nominal thickness to fit the  
If the custom panel is less than 1/4" thick,  
and it fits loosely in the door frame, it can  
be backed up with a piece of filler material  
or foam tape to improve the fit.  
dispenser trim.  
1/4"  
Panel  
the dispenser trim fits over the custom panel and snaps into the  
freezer door.  
• If the panel is less than 0.250" thick, a noticeable gap may be  
created around the dispenser trim. Foam tape may be applied on  
the door to improve the fit.  
• If the panel is more than 0.250" thick, the dispenser trim cannot be  
secured to the door.  
Important Note:  
Maximum total panel weight:  
• Fresh food door panel – 75 lbs.  
• Freezer door panel – 53 lbs.  
• grille panel – 18 lbs.  
39-7/8"  
FREEZER DOOR  
1/4"  
Framed  
Panel  
0.250"  
Thick  
Grille Panel  
9-1/2"  
Ice / Water Dispenser  
1/4" Dispenser Trim  
17-13/16  
Dispenser  
Cutout  
3/4" Overlay Panels  
the overlay dispenser trim is designed to fit a total panel thickness  
of 1.100".  
• If the panel is less than 1.100" thick, a noticeable gap may be  
created around the dispenser trim.  
68-3/8  
3-1/8"  
• If the panel is more than 1.100" thick, the dispenser trim cannot be  
secured to the door.  
the overlay panel must be constructed according to the specifications  
shown to achieve the correct total thickness.  
Freezer  
Panel  
Fresh  
Food  
• Alternative panel construction methods such as securing a  
3/4" panel to a 1/4" backer panel cannot be used. Another method,  
routing a 3/4"-thick panel on all sides, cannot be used. these  
methods will not result in the required 1.100" panel thickness.  
14-9/16"  
24-9/16"  
• When a raised panel design is to be used, a custom middle rail  
is required.  
Dispenser Cutout  
1/4" Backer Panel  
1.100"  
Total  
Thickness  
FREEZER DOOR  
.10" Spacer  
Panel  
15-3/  
Ice / Water Dispenser  
3/4" Overlay  
Panel  
3/4" Overlay Dispenser Trim  
9-5/8"  
For answers to your Monogram,® gE Profileor  
gE® appliance questions, visit our website at  
gEAppliances.com or call  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
Listed by  
Underwriters  
Laboratories  
Specification Revised 3/08  
gE Answer Center® service, 800.626.2000.  
110171  
 
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side  
Refrigerator with Dispenser  
and Water Filter  
Advance Planning for Built-In Custom Side-by-Side Refrigerators  
Use this page to determine door swing  
interaction with adjacent cabinets  
or countertops.  
Frameless Cabinets: the case trim overlaps  
cabinets at the top and sides. therefore,  
frameless cabinets may require filler strips  
to prevent interference with cabinet door swing.  
the opening must allow for filler strips.  
Refrigerator  
23-7/8" From  
Rear of  
Refrigerator  
1"  
2"  
1-3/4"  
3"  
2-3/4"  
Case  
Trim  
3/4"  
1/2"  
1/4"  
1-1/2"  
1-1/4"  
2-1/2"  
2-1/4"  
Top View  
130° Door Swing  
(Factory setting)  
Scale 1:1  
1/4"  
1/2"  
3/4"  
1"  
IMPORTANT NOTE –  
FOR DISPENSER MODELS  
Dispenser models are supplied with  
two dispenser trims, one to fit framed panels  
and one for overlay panels. Dispenser trim fit  
to the custom panel depends on correct  
panel thickness. Framed panels  
must be 1/4" nominal. Overlay panels  
should be constructed as shown  
to accomplish a total  
1.100" thickness.  
1/4"  
1/2"  
3/4"  
1"  
1-1/4"  
Door  
3/4" Overlay  
Panel  
(Nominal Size)  
Listed by  
Underwriters  
Laboratories  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
For answers to your Monogram,® gE Profileor  
gE® appliance questions, visit our website at  
gEAppliances.com or call  
gE Answer Center® service, 800.626.2000.  
Specification Revised 3/08  
110171  
 
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side  
Refrigerator with Dispenser  
and Water Filter  
Advance Planning for Built-In Custom  
Side-by-Side Refrigerators  
Refrigerator  
Use this page to determine door swing  
interaction with adjacent cabinets  
or countertops.  
Case Trim  
23-7/8"  
From Rear of  
Refrigerator  
Frameless Cabinets: the case trim overlaps  
cabinets at the top and sides. therefore,  
frameless cabinets may require filler strips  
to prevent interference with cabinet door swing.  
the opening must allow for filler strips.  
1/4"  
1/2"  
3/4"  
1"  
1-1/4"  
1-1/2"  
Top View  
90° Door Swing  
(Optional setting)  
Scale 1:1  
IMPORTANT NOTE –  
FOR DISPENSER MODELS  
Dispenser models are supplied with two dispenser  
trims, one to fit framed panels and one for overlay  
panels. Dispenser trim fit to the custom panel  
depends on correct panel thickness. Framed  
panels must be 1/4" nominal. Overlay panels  
should be constructed as shown to accomplish  
a total 1.100" thickness.  
1/4"  
Door  
1/2"  
3/4"  
Listed by  
Underwriters  
Laboratories  
1"  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
1-1/4"  
3/4" Overlay  
Panel  
(Nominal Size)  
For answers to your Monogram,® gE Profileor  
gE® appliance questions, visit our website at  
gEAppliances.com or call  
gE Answer Center® service, 800.626.2000.  
Specification Revised 3/08  
110171  
 
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side Refrigerator  
with Dispenser and Water Filter  
Features and Benefits  
• 26.1 cu. ft. total capacity  
• Overhead evaporator  
• Integrated IceSystem – the ice bucket is integrated  
into the icemaker, not the freezer door, freeing up  
valuable storage space  
• Upfront electronic controls with digital readout  
• Multi-shelf halogen light tower (Both fresh food  
and freezer section)  
• Multi-shelf air management tower  
• Climate control drawer with Express Chill,  
Express thaw and Select temp  
• Sealed adjustable humidity produce pan with  
easy access lid and full extension slides  
• Disappearing electronic glass touch dispenser controls  
with proximity sensor  
• Model ZISW420Dr – White dispenser  
• Model ZISB420Dr – Black dispenser (shown)  
Specification Revised 3/08  
110171  
 

Eiki Projector LC SX4 User Manual
Electro Voice Portable Speaker SH 1502 User Manual
Extron electronic Video Game Keyboard MLC 62 IR D User Manual
Fedders Furnace FV95A Series User Manual
Festool Drill CDD12 User Manual
Fisher Price Crib T6338 User Manual
Fusion Portable Speaker MS 0S420 User Manual
Garland Kitchen Grill MWE3W User Manual
Garmin All in One Printer NX420 User Manual
GE Refrigerator 162D3907P004 User Manual