GE Freezer ZKHCSS2 User Manual

Installation  
Instructions  
ZKHCSS2  
Tubular Stainless Steel Handles  
and Handle Side Trim  
Before you begin – Read these instructions completely and carefully.  
Note to Installer: Be sure to leave these instructions with the Consumer.  
Note to Consumer: Keep these instructions with your Owner’s Manual for future reference.  
Right hand door swing models are illustrated in these  
instructions. Follow these same instructions for left hand  
models.  
A
B
D
This kit provides for the installation of Tubular Stainless  
Steel handles or custom handles on 3/4" overlay custom  
panels.  
C
Tools and materials required:  
• #2 Phillips screwdriver  
• Drill and 7/32", 1/8" bits and 7/8" spade bit  
• Custom door panels,  
• Safety glasses  
F
E
• Center punch  
G
• Hammer  
• Pencil  
H
Parts List:  
A. Freezer tubular handle (95376) and  
fresh food tubular handle (95377)  
B. 4 Handle standoffs, 70536  
C. 6 Screws for handle standoffs  
#10-32x1" pan head machine screws (4 required, 2 extra), 36298  
D. 6 Set screws (4 required, 2 extra) 70539  
E. 3/32” Allen wrench for set screws, 70548  
F. 6 Plastic spacers (4 required, 2 extra) 70540  
G. 5 Trim screws (4 required, one extra) 8665  
H. Handle side trim for LH models (75468), trim for RH models (75469)  
STEP 1 REMOVE DOOR AND  
DRAWER HANDLES  
• Open refrigerator door to 90°. Remove the 4 screws  
holding the handle to the door.  
• Remove 4 screws holding handle side trim. Discard all  
screws and trim. Discard handle.  
• Open freezer drawer to access handle and trim.  
Remove and discard handle, retain screws and trim.  
If you are installing custom handles, go to STEP 3.  
 
STEP 3 INSTALL ASSEMBLED PANELS  
Install  
8 Screws  
• Slide assembled panel into the drawer trim.  
• Secure the original drawer trim using original round  
head trim screws.  
Install 4  
Handle Side  
Trim Screws  
• Install custom handles according to the manufacturer’s  
instructions.  
• Slide assembled door panel into  
the trim.  
Custom Trim  
• Determine the correct trim for  
your model (for left or right  
door swing). Place trim against  
the side of the refrigerator door,  
aligned top to bottom. The holes  
in the trim should align to the  
holes in the door. Discard the  
other trim piece.  
Refrigerator  
Door  
Trim to Panel Fit  
• Remove trim. Use a 1/8" bit to drill the semi-punched  
holes in the refrigerator door.  
• Secure the new custom handle side trim using the  
supplied screws.  
-3-  
 
Note: While performing installations described in this book,  
safety glasses or goggles should be worn.  
For Monogram® local service in your area, call  
1-800-444-1845.  
Note: Product improvement is a continuing endeavor at  
General Electric. Therefore, materials, appearance and  
specifications are subject to change without notice.  
®
Monogram.  
We bring good things to life.  
General Electric Company  
Louisville, KY 40225  
Pub. No. 31-46033-2  
Dwg. No. 197D4869P001  
(N.D. 532) 9/02  
75470  
 

Electro Voice Microphone PL37 User Manual
Electro Voice Portable Speaker ECS 12 2 User Manual
Euro Pro Mixer BKM550 User Manual
FieldServer Computer Drive FS 8700 84 User Manual
Fisher Price Cell Phone X14969 User Manual
Ford Automobile 2010 F 250 User Manual
Garland Range C0836 1 User Manual
GE Cordless Telephone FS21828 User Manual
Gemini Stereo Equalizer PDM 3004 User Manual
Global Machinery Company Portable Generator LSSLV User Manual