ColdTech Refrigerator JBB 58 User Manual

COMMERCIAL REFRIGERATOR  
OWNER'S MANUAL  
Back Bar / Direct Draw Coolers  
Models: JBB-58, JBB-80, JDD-58, JDD-80  
This manual contains important information regarding your  
new ColdTech unit. Please read the manual thoroughly prior  
to equipment set-up, operation and maintenance.  
Failure to comply with regular maintenance guidelines outlined  
in this manual may void warranty. MUST READ!!!  
1575 Zephyr Avenue  
(800) 314-4477 (510) 477-3400  
f: (510) 477-3413  
 
INSTALLATION/ OPERATION  
IMPORTANT!!! PLEASE READ BEFORE INSTALLATION  
1) If the unit has recently been transported please let unit stand still for a minimum of 24 hours before  
plugging it in.  
2) Make sure that the unit drops down to desired temperature before loading the unit with product.  
3) Make sure that there is proper ventilation around the unit in the area where it will operate.  
4) Make sure all accessories are installed (i.e. shelves, shelf clips, casters) before plugging the unit in.  
5) Please read through the Operation / Owners Manual in its entirety. Lack of maintenance or misuse of  
the unit will VOID warranty. Please fill out the registration card and send it to the factory.  
CABINET LOCATION GUIDELINES  
1) Install the unit on strong and leveled surfaces  
-unit may make unpleasant noises or malfunction if surface is uneven  
-you may install the unit on a ground surface without the use of the bullet feet provided  
2) Install the unit in an indoor, well-ventilated area  
-unit performs more efficiently in a well-ventilated area  
-for best performance, please maintain clearance of 3" on the back of the unit  
-outdoor use may cause decreased efficiency and damage to the unit  
3) Avoid installation in a high humidity and/or dusty area  
-humidity could cause unit to rust and decrease effeciency of the unit  
-dust collected on condenser coil will cause unit to malfunction. Clean the condenser at least  
once a month with a brush or clean cloth  
-malfunction due to dirty condenser will void warranty  
4) Select a location away from heat and moisture-generating equipment  
-high ambient temperatures will cause the compressor to overwork, leading to higher energy bills  
and gradual breakdown of the unit  
-malfunction due to high ambient temperature will void warranty  
ELECTRICAL  
Please ensure that the required voltage of the compressor is being supplied at all times. Low or high  
voltage can detrimentally affect the refrigeration unit and thereby void its warranty.  
All units should be plugged into a grounded and properly-sized electrical outlet with appropriate  
overcurrent protection. Please refer to the electrical requirements on the unit serial tag located inside the  
unit. Please make sure that your unit has its own dedicated outlet. Do not use an extension cord.  
-3-  
 
TEMPERATURE CONTROLS  
The temperature controls are factory-set to maintain an average temperature of 38 F in refrigerators and 0  
F in freezers. To maintain a different temperature, simply adjust the control knob located inside the unit.  
To decrease the temperature (colder), turn clockwise. To increase the temperature (warmer), turn  
counter-clockwise - see diagram  
6
C AUTION  
7
5
Setting the temperature control to the  
coldest setting may cause the evaporator  
coil to freeze and ice up. This will eventually  
result in a warmer cabinet temperature.  
OFF  
4
Temperatures range  
from (coldest) to  
1
3
2
7
1
TEMPERATURE  
READING  
LIGHT SWITCH OPERATION  
The light switch is located beneath the temperature control, on the evaportor  
cover, which is located inside of your unit, against the right hand wall.  
1) To turn on the light, simply move the toggle switch to "I"  
ON  
2) To turn off the light, simply move the toggle switch to "O"  
OFF  
It is recommended that you turn off the light, whenever possible. This will allow the unit to operate more  
efficiently and reduce your electricity costs.  
BEER DRAIN CONNECTION (APPLICABLE ON "JDD" MODELS ONLY)  
You will notice that your new direct draw unit comes with a plastic bottle, which will collect excess drips or  
overpours from the drip tray. Your unit also comes equipped with an exterior drain option, which will  
bypass the use of the bottle, if you  
would like to allow for the excess  
evaporator cover  
dripping to drain to an external source  
(such as a floor drain). Simply  
disconnect the bottle and connect the  
drain tube into the fitting located on the  
interior drain fitting  
lower right front corner of the interior,  
underneath the evaporator cover.  
Connect a hose (not provided) to the  
fitting located beneath the right door  
on the exterior (as shown) and drain  
exterior drain fitting  
through any source to your liking.  
-4-  
 
SAFETY / WARNING  
Please pay close attention the the safety notices in this section. Disregarding  
these notices may lead to serious injury and/or damage to the unit.  
KEY  
!
ATTENTION  
UNPLUG CORD  
PROPER GROUNDING REQUIRED  
PROHIBITED  
1) To minimize shock and fire hazards, be sure not to overload outlet. Please designate  
one outlet for your unit.  
!
2) Do not use extension cords.  
3) Do not put your hands under the unit when the unit is required to be moved.  
4) When the unit is not in use for a long period of time, please unplug the unit from the  
outlet.  
5) After unplugging the unit, wait at least 10 minutes before re-plugging it. Failure to do  
so could cause damage to the compressor.  
1) To minimize shock and fire hazards, please do not plug or unplug the cord with wet  
hands.  
2) During maintenance and cleaning, please unplug the unit.  
1) To minimize shock and fire hazards, make sure that the unit is properly grounded.  
1) Do not attempt to remove or repair any component unless instructed by factory.  
2) Make sure that the unit is not resting on or against the electrical cord and plug.  
3) To minimize personal injury, do not hang on the doors.  
4) Do not store any flammable and explosive gas or liquids inside the unit.  
5) Do not attempt to alter or tamper with the electrical cord.  
6) Do not set the desired temperature out of the recommended temperature range:  
(Ref: 32 F - 55 F)  
-5-  
 
REGULAR MAINTENANCE  
CLEANING THE CONDENSER COIL  
For efficient operation, it is important that the condenser surface be kept free of dust, dirt, and lint.  
ColdTech recommends cleaning the condenser coil and fins at least once per month. Clean with a  
commercial condenser coil cleaner, available from any kitchen equipment retailer. Brush the condenser  
fins from top to bottom, not side to side. After cleaning, straighten any bent condenser fins with a fin  
comb.  
CLEANING THE FAN BLADES AND MOTOR  
If necessary, clean the fan blades and motor with a soft cloth. If it is necessary to wash the fan blades,  
cover the fan motor to prevent moisture damage.  
CLEANING THE INTERIOR OF UNIT  
When cleaning the cabinet interior, use a solvent of warm water and mild soap. Do not use steel wool,  
caustic soap, abrasive cleaners, or bleach that may damage the stainless steel surface.  
Periodically remove the bin dividers and thoroughly clean the dividers with warm soap and water. If some  
liquid happens to collect on the insdie of the unit, CLEAN IT RIGHT AWAY. DO NOT LEAVE THE LIQUID  
SITTING INSIDE OF THE UNIT. This will cause corrosion and will deteriorate the life of the unit.  
WAR NING  
Disconnect power cord before cleaning any parts of the unit.  
TROUBLE SHOOTING  
Before requesting any service on your ColdTech unit, please check the following points. Service calls  
resulting from lack of maintenance or misuse is not covered under warranty and also may void warranty.  
Please note that this guide serves only as a reference for solutions to common problems.  
-6-  
 
SYMPTOM  
Compressor not running.  
POSSIBLE CAUSE  
Fuse blown or circuit breaker tripped.  
CORRECTIVE ACTION  
Replace fuse or reset circuit  
breaker.  
Power cord unplugged.  
Thermostat set too high.  
Plug in power cord.  
Set thermostat to lower  
temperature.  
Cabinet in defrost cycle.  
Wait for defrost cycle to finish.  
Condensing unit runs for  
long periods of time.  
Excessive amount of warm product  
placed in cabinet.  
Prolonged door opening or door ajar.  
Allow adequate time for  
product to cool down.  
Ensure doors are closed when  
not in use. Avoid opening  
doors for long periods of time.  
Ensure gaskets are snapped in  
completely. Remove gasket  
and wash with soap and water.  
Check condition of gasket and  
replace if necessary.  
Door gasket(s) not sealing properly.  
Dirty condenser coil.  
Evaporator coil iced over.  
Clean the condenser coil.  
Unplug unit and allow coil to  
defrost. Make sure thermostat  
is not set too cold. Ensure that  
door gasket(s) are sealing  
properly.  
Cabinet temperature is  
too warm.  
Thermostat set too warm.  
Blocking air flow.  
Set thermostat to lower  
temperature.  
Re-arrange product to allow for  
proper air flow. Make sure  
there is at least four inches of  
clearance from evaporator.  
Allow adequate time for  
product to cool down.  
Excessive amount of warm product  
placed in cabinet.  
Fuse blown or circuit breaker tripped.  
Replace fuse or reset circuit  
breaker.  
Dirty condenser coil.  
Prolonged door opening or door ajar.  
Clean the condenser coil.  
Ensure doors are closed when  
not in use. Avoid opening  
doors for long periods of time.  
(see above)  
Evaporator coil iced over.  
Loose part(s).  
Cabinet is noisy.  
Locate and tighten loose  
part(s).  
Tubing vibration.  
Ensure tubing is free from  
contact with other tubing or  
components.  
-7-  
 
The New Symbol of Innovation™  
MEMO  
RETAIN THIS MANUAL FOR FUTURE REFERENCE  
Please read the entire manual carefully before installation and operation. If certain recommended  
procedures are not followed, warranty claims will be denied.  
Notice: ColdTech reserves the right to make changes in design and specifications without prior notice.  
MODEL #: _______________________________  
SERIAL #: _______________________________  
PURCHASE DATE #: _______________________  
 

Conair Electric Shaver HCT420CSV User Manual
Cradlepoint Network Cables CBA750 User Manual
Curtis DVD Player DVD1043 User Manual
Digicom Network Router ADSL Router User Manual
Dynex Laptop DX WLCMBO2 User Manual
Escient Home Theater System SE D1 User Manual
Fisher Paykel Oven BI601 Series User Manual
Fisher Paykel Ventilation Hood HS90CSX1 User Manual
Fundex Games Board Games Regal 12 Backgammon User Manual
Global Machinery Company Trimmer BHT500 User Manual