Canon Camera Lens 3558B002 User Manual

EF-S18-135mm f/3.5-5.6 IS  
ENG  
 
Instruction  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not  
cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause  
undesired operation.  
Do not make any changes or modifications to the equipment  
unless otherwise specified in the instructions. If such changes or  
modifications should be made, you could be required to stop  
operation of the equipment.  
This equipment has been tested and found to comply with the  
limits for a class B digital device, pursuant to part 15 of the FCC  
Rules. Tse limits are designed to provide reasonable protection  
againshmful interference in a residential installation. This  
ment generates, uses and can radiate radio frequency  
y and, if not installed and used in accordance with the  
inructions, may cause harmful interference to radio  
communications.  
However, there is no guarantee that interference will not occur in  
a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of  
the following measures:  
a Safety Precautions  
Do not look at the sun or a bright light source  
through the lens or camera. Doing so could  
result in loss of vision. Looking at the sun directly  
through the lens is especially hazardous.  
Whether it is attached to the camera or not, do  
not leave the lens under the sun without the  
lens cap attached. This is to prevent the lens from  
concentrating the sun’s rays, which could cause a  
fire.  
Handling Cautions  
If the lens is taken from a cold environment i
a warm one, condensation may develoon th
lens surface and internal parts. To prevnt  
condensation in this case, first put the lens ito n  
airtight plastic bag before taking it from a cold to  
warm environment. Then take out the lens after it  
has warmed gradually. Do the same when taking  
the lens from a warm environment into a cold one.  
• Do not leave the lens in excessive heat such as in  
a car in direct sunlight. High temperatures can  
cause the lens to malfunction.  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Consult the dealer or an experienced radio/TV technician for  
help.  
This Class B digital apparatus complies with Canadian ICES-003.  
ENG-2  
 
Nomenclature  
Focus mode switch (4)  
Zoom position index (5)  
Hood mount (5)  
Filter mounting  
thread (8)  
Focusing ring (4)  
Zoom ring (5)  
Contacts  
(4)  
Image stabilizer switch (6)  
Lens mount index (4)  
For detailed information, reference page numbers are provided in parentheses (**).  
ENG-3  
 
Mounting and Detaching the Lens  
Setting the Focus Mode  
1
2
See your camera’s instructions for details on  
mounting and detaching the lens.  
To shoot in autofocus (AF) mode, set the focus  
mode witch to AF.  
¡After detaching the lens, place the lens with the  
rear end up to prevent the lens surface and  
electrical contacts from getting scratched.  
¡If the contacts get soiled, scratched, or ave  
fingerprints on them, corrosion or faulty  
connections can result. The camera and lens  
may not operate properly.  
use nly manual focusing (MF), set the focus  
de switch to MF, and focus by turning the  
focusing ring.  
¡Do not touch the rotating parts of the lens while  
autofocus is active.  
¡Do not adjust focus manually when the focus  
mode switch is set to AF.  
¡If the contacts get soiled or have fingerprints on  
them, clean them with a soft cloth.  
¡If you remove the lens, cover it with the dust  
cap. To attach it properly, align the lens mount  
index and the ¢ index of the dust cap as shown  
in the diagram, and turn clockwise. To remove  
it, reverse the order.  
ENG-4  
 
Hood (Sold Separately)  
Zooming  
3
4
The EW-73B hood can keep unwanted light out  
of the lens, and also protects the lens from rain,  
snow, and dust.  
To attach the hood, align the hood’s attachme
position mark with the red dot on the front of t
lens, then turn the hood as shown by tharrow  
until the lens' red dot is aligned with the oods  
stop position mark.  
To zoom, turn the lens’ zoom ring.  
minmum focusing distance differs at  
derent focal lengths.  
18mm: 0.49 m / 1.6 ft.  
50mm: 0.47 m / 1.5 ft.  
135mm: 0.45 m / 1.5 ft.  
Shooting magnification  
18mm: 0.05×  
50mm: 0.12×  
135mm: 0.21×  
The hood can be reverse-mounted on the lens  
for storage.  
¡Part of the picture may be blocked if the hood is  
not attached properly.  
¡When attaching or detaching the hood, grasp  
the base of the hood to turn it. To prevent  
deformation, do not grasp the rim of the hood to  
turn it.  
Be sure to finish zooming before focusing.  
Changing the zoom ring after focusing can affect  
the focus.  
ENG-5  
 
Image Stabilizer  
5
You can use the image stabilizer in AF or MF  
mode.  
¡The Image Stabilizer cannot compensate for a  
blurred shot caused by a subject that moved.  
¡The Image Stabilizer may not be fully effective if  
you shoot from a violently shaking vehicle or  
other transportation.  
This function provides optimal image stabilization  
depending on shooting conditions (such as  
shooting still subjects and following shots).  
¡The Image Stabilizer consumes more power  
than normal shooting, so fewer shots can be  
taken if you use the function.  
¡Wen shooting a still subject, it compensates for  
camra shake in all directions.  
¡It compensates for vertical camera shake during  
following shots in a horizontal direction, and  
compensates for horizontal camera shake  
during following shots in a vertical direction.  
¡Using a tripod also stabilizes the image.  
However, depending on the kind of tripod and  
shooting conditions, sometimes it may be better  
to turn off the Image Stabilizer function.  
Set the STABILIZER switch to  
¡If you are not going to use the image  
stabilizer function, set the switch to  
1
.
When you press the shutter button  
¡The stabilizer is equally effective for hand-held  
photography and photography with a monopod.  
2halfway, the Image Stabilizer will  
start operating.  
¡
The image stabilizer function also operates when the  
lens is used with an Extension Tube EF12 ll or EF25 ll.  
If you set the camera’s Custom Function to change the  
assigned button to operate the AF, the Image Stabilizer will  
operate when you press the newly assigned AF button.  
¡Make sure the image in the viewfinder is  
stable, then press the shutter button the  
rest of the way down to take the picture.  
¡
ENG-6  
 
Image Stabilizer  
The image stabilizer in this lens is effective for hand-held shots under the following  
conditions.  
¡In semi-darkened areas such as indoors or  
outdoors at night.  
¡When panning subjects in motion.  
¡In locations where flash photography is  
prohibited, such as art museums and theater  
stages.  
¡In situations where your footing is uncertain.  
¡In situations where fast shutter settings cannot  
be used.  
ENG-7  
 
Filters (Sold Separately)  
Extension Tubes (Sold Separately)  
6
7
You can attach filters to the filter mounting  
thread on the front of the lens.  
You can attach Extension Tube EF12 II or EF25  
II for magnified shots. The shooting distance and  
magnification are shown below.  
¡Only one filter may be attached.  
¡If you need a polarizing filter, use the Canon  
Circular Polarizing Filter PL-C B (67mm).  
¡To adjust the polarizing filter, first remove the  
lens hood.  
Camera-to-Subject  
Magnification  
Distance (mm)  
Near  
304  
252  
Far  
Incompatible  
1551 0.38×  
Incompatible  
806 0.59×  
Near  
Far  
18mm  
135mm  
18mm  
EF12 II  
EF25
0.09×  
0.21×  
35mm  
Manual focusing is recommended for accurate  
focusing.  
ENG-8  
 
Specifications  
8
Focal Length/Aperture  
Lens Construction  
Minimum Aperture  
Angle of View  
18 – 135 mm f/3.5 – 5.6  
12 groups, 16 elements  
f/22 – 36*1  
Diagonal: 74° 20’ – 11° 30’  
Horizontal: 64° 30’ – 9° 30’  
0.45 m/1.5 ft. (at 135mm)*2  
0.21× (at 135 mm)  
327 × 503 mm/12.9 × 19.8 inch (at 0.49 m/1.6 ft.) –  
75 × 112 mm/3.0 × 4.4 inch (a0.45 m/1.5 ft.)  
67 mm/2.6 inch  
Vertical: 45° 30’ – 6° 20’  
Min. Focusing Distance  
Max. Magnification  
Field of View  
Filter Diameter  
Max. Diameter and Length  
Weight  
Hood  
75.4 × 101 mm/3× 4inch  
455 g/16.0 oz  
EW-73B Sold setely)  
E-67/E-67 II  
Lens Cap  
Case  
LP1116 (Sold separately)  
*1 Applies to 1/3-stop increments. With 1/2-stop increments, it will be f/22-38.  
*2 The minimum focusing distance differs at different focal lengths.  
¡Equivalent to 29-216 mm in the 35mm film format.  
¡The lens length is measured from the mount surface to the front end of the lens. Add 21.5 mm to include the E-67  
lens cap and dust cap, and 24.2 mm for the E-67 II.  
¡The size and weight listed are for the lens only, except as indicated.  
¡The EF1.4X II/EF2X II extenders cannot be used with this lens. There are no compatible close-up lenses.  
¡Aperture settings are specified on the camera. The camera automatically compensates for variations in the  
aperture setting when the camera is zoomed in or out.  
¡All data listed is measured according to Canon standards.  
¡Product specifications and appearance are subject to change without notice.  
ENG-9  
 
 
0812Ni © CANON INC. 2009  
CT1-8565-007  

Belkin Network Router F5L049 User Manual
Bissell Vacuum Cleaner BS 7920F User Manual
Black Decker Vacuum Cleaner 244279 00 User Manual
Blue Rhino Outdoor Fireplace 252726 User Manual
Bose Speaker System 149393 User Manual
Breville Oven BPZ600XL User Manual
Briggs Stratton Blower 326400 User Manual
Briggs Stratton Switch 071037 User Manual
Canon All in One Printer 5784B020 User Manual
Casio Electronic Keyboard CZ 3000 User Manual