Bobrick Bathroom Aids B 5181 User Manual

INSTALLATION INSTRUCTIONS  
BOBRICK MODEL B-5181 REvERSIBLE SOLID PhENOLIC FOLDING ShOWER SEAT  
Shower Seat in  
Reversed Position  
33''  
840mm  
6-3/4''  
170mm  
19-1/2''  
495mm  
22-5/16''  
565mm  
16-1/2''  
420mm  
5-1/2''  
140mm  
13-3/8''  
340mm  
Finish Face of Wall  
Bolts Removed  
and Replaced  
to Reverse  
1-3/8''  
35mm  
Seat Position  
17-5/16''  
440mm  
Mounting  
Flanges (2)  
21-7/8''  
555mm  
20-15/16''  
530mm  
14-7/16''  
365mm  
4-1/2''  
115mm  
S
S
S
S
S
Concealed wall  
backing to  
comply with  
local building  
codes, not  
furnished  
by Bobrick.  
S
S
Support  
Tube  
Universal/Barrier-Free  
Recommended  
Mounting Height  
S
S
S
S
9-3/8''  
240mm  
2-1/4''  
55mm  
7-1/4''  
185mm  
Dia.  
Bolt Circle  
*17'' to 19''  
430 to 485mm  
Baseplate  
with Spring  
2-1/4''  
55mm  
1-1/8''  
30mm  
Guide Bracket  
S
S
S
Finish Face of Floor  
*Consult local building codes  
Left-Hand Seat Shown  
Installation to Wall. Secure unit to wall at points indicated by an S, with the two Mounting Flanges located at top and the Baseplate  
and Guide Bracket below. The bottom of the Support Tube must be positioned within the Baseplate and Guide Bracket before they are  
secured to wall. * Mounting height of shower seat must comply with local building codes.  
1. Install Mounting Flanges to Wall.  
A. Locate seat horizontally on wall to comply with local building codes.  
B. Use Mounting Flanges as templates to mark holes.  
1) Check to make sure seat surface is horizontal and Mounting Flanges are flat against wall.  
2) Make sure holes marked for Mounting Flanges align with wall backing.  
C. Drill holes for Mounting Flange fasteners and secure Mounting Flanges to wall with appropriate fasteners.  
D. Check to see if seat moves freely from horizontal to vertical position.  
IMPORTANT NOTES  
1) For stud wall construction, install backing (not furnished by Bobrick) (see Figure 2). Backing must be provided before  
the finished shower wall is applied. Secure with #14 x 2-1/2" (6.3 x 65mm) stainless steel mounting screws furnished by  
manufacturer.  
2) For prefabricated shower stalls, adequate backing must be provided by the shower stall manufacturer (see Figure 2).  
Secure with #14 x 2-1/2" (6.3 x 65mm) stainless steel mounting screws furnished by manufacturer.  
3) For concrete walls, provide fiber plugs or expansion shields for use with furnished screws, or provide 1/4" (6mm) toggle  
bolts or expansion bolts. Wall anchors not furnished by Bobrick.  
CAUTION:This shower seat is no stronger than the anchors and walls to which it is attached and, therefore, must be  
firmly secured in order to support the loads for which it is intended. Consult and comply with local building codes.  
2. Install Baseplate with Spring and Guide Bracket to Wall.  
A. Support seat in level horizontal position.  
B. Locate Guide Bracket on wall with bottom center of Support Tube resting on bottom of Guide Bracket (see Figure 2).  
C. Mark holes on wall using Guide Bracket as a template.  
D. Drill holes in wall for appropriate fasteners (see Figure 3). Install fasteners.  
E. Place Baseplate on wall with curled spring at top aligning holes in Baseplate with fasteners.  
F. Place Guide Bracket over Support Tube and fasten to wall.  
continued . . .  
 

Bertazzoni Slow Cooker WD60CONX 12 User Manual
Black Decker Rice Cooker HS1000 User Manual
Blanco Indoor Furnishings 157 013 User Manual
Blomberg Clothes Dryer TKF 9431 A User Manual
Bosch Appliances Security Camera 5000 PTZ User Manual
Brocade Communications Systems Iron 53 1001763 02 User Manual
Brother Fax Machine FAX 1355 User Manual
Canon Camcorder xha1 User Manual
Casio Electronic Keyboard LK94TVES1B User Manual
Chauvet Work Light 15090394 User Manual