Pelco Blower HB6000 220 User Manual

®
HB6000, HB6000/220, and  
HB6024  
Heater/Blower Kits  
Installation/Operation  
Manual C496M (12/90)  
2.0 SCOPE  
1.0 WARNINGS  
The information within this manual covers the installa-  
tion of the HB6000, HB6000/220, and HB6024 Heater/  
Blower Kits.  
Priortoinstallationanduseofthisproduct,thefollowing  
WARNINGS should be observed.  
1. Installation and servicing should only be done by  
Qualified Service Personnel and conform to all  
Local codes.  
3.0 DESCRIPTION  
The HB6000 (120 VAC), HB6000/220 (230 VAC), and  
the HB6024 (24 VAC) are field installed heater/blower  
kits for the HS1000 and HS6000 series high security  
enclosures. These heater/blower kits will help stabilize  
the internal enclosure temperatures when the enclosures  
are subjected to more extreme conditions.  
2. Installation should be in accordance with all  
applicablelocalandnationalelectriccodes,utilizing  
approve materials only.  
3. OnlyusereplacementpartsrecommendedbyPelco.  
The heaters provide 80 watts of heat thermostatically  
controlled to turn ON at 40°F (4.44°C) and OFF at 60°F  
(15.56°C).  
Please thoroughly familiarize yourself with the informa-  
tion in this manual prior to installation and operation.  
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827  
International customers call (1-559) 292-1981 or FAX (1-559) 348-1120  
 
4.2 BLOWER/PCB ASSEMBLY  
3.4 POWER REQUIREMENTS  
1. Open the cover or access door(s).  
The blower and heater require a 24 VAC/120 VAC/230  
VAC, 50/60 Hz single phase power source. They use  
the following wattage when in operation.  
2. On the HS1000, the blower/PCB bracket is de-  
signed to attach to any two (2) adjacent studs re-  
taining the bottom plate. On the HS6000, the  
blower/PCB bracket is designed to attach to the  
two (2) studs at the bottom of the window.  
Blower:  
Heater:  
4.5 watts  
80 watts  
4.0 INSTALLATION  
3. On the HS1000, remove any two (2) adjacent nuts  
and washers retaining the bottom plate to the  
mounting frame. On the HS6000, remove the nuts  
and washers retaining the bottom of the window.  
To install the HB6000, HB6000/220, and HB6024 per-  
form the following steps. Refer to Figure 1.  
4.1 HEATER ASSEMBLY  
4. Place the blower/PCB bracket over the studs and  
replace and tighten the hardware  
1. Open the cover or access door.  
2. The heater brackets are designed to attach to two  
(2) adjacent studs retaining the window.  
3. Remove any two (2) adjacent nuts and washers  
(preferably at the bottom of the window) on both  
sides of the window.  
4. Place the heater brackets on the studs, heaters  
angled away from the window, and replace and  
tighten the hardware.  
Figure 1. HB6000, HB6000/220, and HB6024 Assembly  
Pelco Manual C496M (12/90)  
3
 
4.3 HEATER/BLOWER WIRING  
4.4 ELECTRICAL CONNECTION  
The blower is factory wired to the PCB assembly.  
After the cable has been routed, all wire connections  
should be made (i.e., video, lens, camera power, heat-  
ers). A 6-position terminal block has been provided to  
assist in this.  
Connect the heaters to the PCB assembly as shown in  
the respective wiring diagrams (refer to Figure 2, Fig-  
ure 3, or Figure 4).  
CAUTION: When using a single power  
source for both the camera and accessories, the  
camera power consumption must be taken into  
consideration when determining the wire gauge.  
Also, make certain that all electrical connec-  
tions are done properly and meet electrical  
codes.  
SupplyAC line voltage (230 VAC, 120 VAC, or 24 VAC)  
as shown.  
Figure 2. HB6000/220 Heater/Blower Kit Wiring Diagram (230 VAC)  
4
Pelco Manual C496M (12/90)  
 
Figure 3. HB6000 Heater/Blower Kit Wiring Diagram (120VAC)  
Figure 4. HB6024 Heater/Blower Kit Wiring Diagram (24 VAC)  
Pelco Manual C496M (12/90)  
5
 
5.0 MECHANICAL PARTS LIST FOR HB6000/220 (230 VAC) HEATER/BLOWER KIT  
Item No.  
Qty  
Description  
Part Number  
1
2
3
4
5
6
7
1
1
1
2
1
2
1
Bracket, Fan/PCB, HB6000  
HB60004000COMP  
PCB9000256ASSY  
MM750010003  
HB60004001COMP  
EH450010256  
PCB Assembly, Term/Thermo, EH4500 Series  
Fan 10CFM 2.36" SQ 115 VAC  
Bracket, Heater, HB6000  
Insulator, PCB, EH4500, 6.25" x 2.00"  
Heater Blanket 2" x 2" 115V40W  
Resistor 3K Ohm, 10W  
EHWD10087  
RES003.0K10.00  
MECHANICAL PARTS LIST FOR HB6000 (120 VAC) HEATER/BLOWER KIT  
Item No.  
Qty  
Description  
Part Number  
1
2
3
4
5
6
1
1
1
2
1
2
Bracket, Fan/PCB, HB6000  
PCB Assembly, Term/Thermo, EH4500 Series  
Fan 10CFM 2.36" SQ 115VAC  
Bracket, Heater, HB6000  
Insulator, PCB, EH4500, 6.25" x 2.00"  
Heater Blanket 2" x 2" 115V40W W/PSA  
HB60004000COMP  
PCB9000256ASSY  
MM750010003  
HB60004001COMP  
EH450010256  
EHWD10087  
MECHANICAL PARTS LIST FOR HB6024 (24 VAC) HEATER/BLOWER KIT  
Item No.  
Qty  
Description  
Part Number  
1
2
3
4
5
6
7
1
1
1
2
1
2
1
Diode Bridge Rectifier 1A400PRV MOT  
PCB Assy, Term/Thermo, EH4500 Series  
FAN 11CFM 2.36" SQ. 24VDC, D24-B10TRW  
Bracket, Heater, HB6000  
Insulator, PCB, EH4500, 6.25" x 2.00"  
Heater Blanket 2" x 2" 24V40W W/PSA  
Diode Bridge Rectifier 1A400PRV MOT  
DIOMDA104  
PCB9000256ASSY  
ED210005  
HB60004001COMP  
EH450010256  
EHHK10087  
DIOMDA104  
6
Pelco Manual C496M (12/90)  
 
6.0 SPECIFICATIONS  
ELECTRICAL  
Input Voltage: 24VAC/120VAC/230VAC,50/60Hz  
Electrical  
Connection:  
One 10-position terminal block (in-  
put)  
One 6-pin lens connector  
Two (2) 10-position terminal blocks  
for internal wiring  
Pelco Manual C496M (12/90)  
7
 
7.0 WARRANTY AND RETURN  
INFORMATION  
WARRANTY  
RETURNS  
Pelco will repair or replace, without charge, any merchandise proved  
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate  
of shipment.  
In order to expedite parts returned to the factory for repair or credit, please  
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an  
authorization number (CA number if returned for credit, and RA number  
if returned for repair).  
Exceptions to this warranty are as noted below:  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and  
keyboard).  
Three years on Camclosure® and fixed camera models, except the  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,  
and MC3651H-2X camera models, which have a five-year warranty.  
All merchandise returned for credit may be subject to a 20% restocking  
and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the  
assigned CA or RA number and freight should be prepaid. Ship to the  
appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto  
Rico, send goods to:  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and  
DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, includ-  
ing when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding  
wiper blades).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto  
Rico and are instructed to return goods to the USA, you may do one of the  
following:  
Eighteen months on DX Series digital video recorders, NVR300  
Series network video recorders, and EnduraSeries distributed  
network-based video products.  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
One year (except video heads) on video cassette recorders (VCRs).  
Video heads will be covered for a period of six months.  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods  
to:  
Six months on all pan and tilts, scanners or preset lenses used in  
continuousmotionapplications(thatis,presetscan,tourandautoscan  
modes).  
Pelco c/o Expeditors  
473 Eccles Avenue  
Pelco will warrant all replacement parts and repairs for 90 days from the  
date of Pelco shipment. All goods requiring warranty repair shall be sent  
freight prepaid to Pelco, Clovis, California. Repairs made necessary by  
reason of misuse, alteration, normal wear, or accident are not covered  
under this warranty.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco assumes no risk and shall be subject to no liability for damages or  
loss resulting from the specific use or application made of the Products.  
Pelco’s liability for any claim, whether based on breach of contract,  
negligence, infringement of any rights of any party or product liability,  
relating to the Products shall not exceed the price paid by the Dealer to  
Pelco for such Products. In no event will Pelco be liable for any special,  
incidental or consequential damages (including loss of use, loss of profit  
and claims of third parties) however caused, whether by the negligence  
of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The  
Dealer may also have additional rights, which are subject to variation from  
state to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800)  
289-9100 or (559) 292-1981 to obtain a Repair Authorization number  
(RA), and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice  
number  
3. Details of the defect or problem If there is a dispute regarding the  
warranty of a product which does not fall under the warranty conditions  
stated above, please include a written explanation with the product  
when returned.  
Method of return shipment shall be the same or equal to the method by  
which the item was received by Pelco.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
Pelco, the Pelco Logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
© Copyright 1990, Pelco. All rights reserved.  
8
Pelco Manual C496M (12/90)  
 

PB Heat Boiler EC Series User Manual
Philips Cordless Telephone VOIP8410 User Manual
Philips Flat Panel Television 15PF9945 37 User Manual
Philips Range SBC SC468 User Manual
Philips Trimmer HP6375 01 User Manual
Philips TV Video Accessories SVC2546W User Manual
Pioneer Car Video System AVH P7850DVD User Manual
Pioneer DJ Equipment mep 7000 User Manual
Planar Computer Monitor PL1911MW User Manual
Polycom IP Phone 1725 16844 001 User Manual