POSIFLEX Business Machines Computer Monitor TM4000 Series User Manual

TM4000 Series  
Touch Monitor  
USER’S MANUAL  
Rev. : A  
I. FEATURES  
·
·
·
·
·
·
·
·
·
·
Most stable touch monitor for industrial and commercial use  
Application covers POS, POI (Kiosk), -Factory Automation etc.  
High quality 12.1”/15” TFT LCD panel with scaling function for full screen display  
Resistive type extra long life touch panel with touch resolution 1024 x 1024  
Recommended. LCD resolution: 800 x 600 for 12.1” and 1024 x 768 for 15”  
1 up 3 down USB Hub (option), relay PS/2 keyboard & PS/2 mouse connectors  
Tilt and height adjustable yet robust and wobble free construction  
Spill proof and easy maintenance structure allowing easy cleaning  
Touch functions include left/right button, double click, drag & drop  
Touch beep can be pitch adjusted and enabled/disabled by software control  
FCC NOTICE  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to  
comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to  
provide reasonable protection against interference when operated in a commercial environment. Operation of this  
equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to  
take whatever measures to correct the interference.  
WARRANTY LIMITS  
Warranty will terminate automatically when the machine is opened by any person other than the authorized  
technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow  
the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or  
hazard caused by improper application.  
ABOUT THIS MANUAL  
This manual assists the user to utilize the TOUCH Monitor TM4000 series. These series provide versatile font  
formats and support various instruction sets. These series of products receive instructions in serial communication  
protocols and is capable of entering pass through mode so that all instructions received pass on to next connected serial  
device if properly configured.  
The manufacturer of the TM4000 series heartily apologizes to the user for reserving the right to change or to  
modify this manual without notice due to the rapid and constant progress and improvement on science and technology.  
Ó Copyright Mustek Corp. 2001  
TRADE MARKS AND SERVICE MARKS  
POSIFLEX is a registered trademark of Mustek Corp..  
Other brand and product names are trademarks and registered trademarks and service marks of their respective  
owners.  
CMANUTM4000-1  
1
 
B. SIDE VIEWS  
Power on/off switch  
(Press on white dot  
to turn power on)  
Latch hole for cable cover  
Push in this direction  
to adjust the tilt angle  
of the display panel  
Lock/release lever  
C. REAR VIEW  
Lock/release button to detach the main unit  
Lock/release lever for tilt angle adjust  
Cable Exit  
V. INPUT / OUTPUT PORT  
a. DC 12V  
b. USB TO PC f. USB 1  
e. USB 2  
i. TO (PC) RS232 PORT (option)  
j. KB  
c. CRT  
g. MOUSE  
k. TO (PC) KB PORT  
d. USB 3  
h. TO (PC) MOUSE PORT l. MSR (option)  
j
e
g
h
k
i
a
b
c
d
f
l
3
 
VI. OPTION ITEMS  
1. Wall Mount Kit  
2. Integrated MSR: ISO 2 or 3 track or JIS II with PS/2 interface  
3. RS232 interface touch controller for TM4012E or TM4015E only.  
(PS/2 interface controller will be hereby deleted for this option)  
4. USB hub (1 up 3 down)  
VII. INSTALLATION  
1. For best cable routing effect, please do next step to place all required cables  
into the cable passage in the stand assembly.  
2. Press down the lock/release button on stand assembly when lifting the main  
unit to separate main unit from the stand. Route all cables to be connected to  
PC or other device through the cable exit in stand assembly. (Open the metal  
plate first if necessary.) Make all the monitor end of cables to come out of  
the stand assembly like the right picture below.  
Matching Pegs  
Matching Holes  
Round Part  
Slot Part  
Removal  
Hollow  
Hook the main unit back on stand assembly by matching the matching pegs  
to round part of matching holes and slide them down to slot part till the rear  
latch clicks. It is recommended that the terminal be hooked onto the lower  
set of holes for better stability.  
3. Push the lock/release lever on the base backward to adjust the stand to the  
most horizontal position for ease of operation. Insert the tip of the latchkey  
into a latch hole on one side near bottom of the main unit. Turn this key  
counterclockwise to the end and take it out. Do the same on the opposite  
side. Open the cable cover by pulling at the removal hole.  
4
 
4. Cable connection guide:  
Cable  
TM4000 port  
CRT  
External device  
CCBLA-366  
VGA port of PC  
CCBLA-367  
TO (PC) KB PORT  
USB TO PC  
PS/2 keyboard port of PC  
USB port of PC  
CCBLA-383  
CCBLA-384  
TO (PC) MOUSE PORT PS/2 mouse port of PC  
Cable from external device KB  
PS/2 keyboard  
PS/2 mouse  
Cable from external device MOUSE  
Cable from external device USB 1 ~ USB 3  
Cable from power adaptor DC 12V  
External USB devices  
Power adaptor  
Among these, power adaptor, CCBLA-366 and CCBLA-384 are crucial vital  
connections for functionality of TM4000 series.  
5. Consolidate the cables and close and lock the cable cover.  
6. Connect the power cord between power adaptor and a suitable power socket.  
7. Adjust for best viewing tilt angle then proceed for driver installation.  
VIII. DRIVER INSTALLATION  
1. PS/2 Interface Touch Controller:  
Please find in the attached Posiflex product information CDROM for PS/2  
interface touch controller driver under subdirectory \Drivers\TM4000. In case  
this subdirectory is not found in the CDROM received, please use identical  
driver from relevant product such as \Drivers\TP6000\Touch\PS-II\TCTM_W98  
for Win98 system or \Drivers\TP6000\Touch\PS-II\TCTM_WNT for NT4.0 or  
Win2000 system. Click SETUP.EXE to install the driver into system and a  
utility program Posiflex Touch Terminal Manager for touch calibration.  
2. Optional RS232 Interface Touch Controller:  
Similar to the above, please find in the attached Posiflex product  
information CDROM for RS232 interface touch controller driver under  
subdirectory \Drivers\TM4000. In case this subdirectory is not found in the  
CDROM received, please use identical driver from relevant product such as  
\Drivers\TP6000\Touch\ RS232\RSTC_W9x for Win9x system. Click  
SETUP.EXE to install the driver into system and a utility program for touch  
calibration. Same approach applies for other operating system.  
5
 
IX. LED INDICATION  
·
·
Orange: standby  
Green: power on  
X. OSD (ON SCREEN DISPLAY) SCREEN ADJUST FUNCTION  
Power/Standby LED  
“+” button: to increase setting.  
“-” button: to decrease setting.  
“NEXT” button: to go to next option function.  
“OSD” button: to enter OSD setting menu or submenu, or to execute designated  
operation shown in operation shown in operation guide area.  
OSD description as below:  
POSIFLEX  
OSD Setting Menu  
Brightness  
Option  
function list  
Option function selected  
Contrast  
Auto Adjust  
Exit  
Parameter setting or  
Operation guide area  
Press “OSD” button on front bezel below the LCD panel when any  
normal screen is displayed to activate the OSD functions (on screen display  
adjustment). The main menu will pop up on LCD screen in the layout shown  
above. In OSD main menu, it will disappear if no button for OSD setting is  
pressed within a period of time (about 30 seconds).  
At this screen, pressing “+” button will increase screen brightness,  
pressing “-” button will decrease screen brightness and pressing “NEXT” button  
will change the selected option function to “Contrast” as next drawing.  
6
 
At this screen, pressing “+” button will  
increase screen contrast, pressing “-” button will  
decrease screen contrast and pressing “NEXT”  
button will change the selected option function to  
“Auto Aujust”.  
POSIFLEX  
OSD Setting Menu  
Brightness  
Contrast  
Auto Adjust  
Exit  
When the option function selected comes  
to “Auto Adjust”, the operation guide area will  
indicate  
OSD button to  
Auto Adjust” as  
“Press  
POSIFLEX  
OSD Setting Menu  
Brightness  
Contrast  
Auto Adjust  
Exit  
drawing at right. After OSD button pressed, “Auto  
adjusting, please wait” will show up in operation  
guide area till operation completed. Pressing  
“NEXT” button will change the selected option  
function to “Exit”.  
POSIFLEX  
When the  
Press OSD button to Auto Adjust  
OSD Setting Menu  
option  
function  
Brightness  
Contrast  
Auto Adjust  
Exit  
selected is “Exit”, the operation guide area will  
indicate “Press OSD button to Exit” as drawing at  
left. Pressing “NEXT” button will change the  
selected option function back to “Brightness”  
again, pressing OSD button, the OSD Setting  
Menu will be closed immediately.  
Press OSD button to Exit  
XI. TROUBLE SHOOTING  
In case of any malfunction, please check the following points in sequence  
to resolve it.  
1. If there is no power indication, please check the power connection.  
2. If there is no picture display with power LED on, please check the video  
signal connection.  
3. If the display is abnormal, please reset the monitor: Please turn off the  
monitor and then keep pressing any of the OSD button when turning the  
monitor back to ON.  
7
 
4. If there is no touch function, please check the connection of the PS/2 Mouse  
cable with green connectors (CCBLA-384) or the RS232 cable (CCBLA-  
368) for optional RS232 interface touch controller. Please pay particular  
attention on whether the PS/2 Mouse cable is connected to the right  
connector on TM4000 series or whether the RS232 cable is connected to the  
right COM port of PC according to the driver installation.  
5. The USB hub function could be disrupted if any current overload of the  
down stream USB device occurs. Please turn off the TM4000 series and turn  
it back on to reinstate the USB hub. If problem still presents, please  
disconnect the down stream USB device and check the current loading of  
that USB device.  
8
 

PB Heat Boiler MI MIH series User Manual
Philips DVD VCR Combo DVP720SA User Manual
Philips Portable CD Player CDP 200 User Manual
Philips Power Supply 6FF3FP User Manual
Philips Stereo System MZ3 User Manual
Pioneer Stereo Receiver SX 680 User Manual
Planar Car Video System PS7050 User Manual
Planar Computer Monitor LB1500R User Manual
Polycom Conference Phone 3726 17776 001 User Manual
Polycom Conference Phone Conference Phone User Manual