NETGEAR Network Router WG602V4 User Manual

f. Turn on your computer and verify the LED behavior on the front of the wireless  
access point.  
Tip: Before you deploy your wireless access point, reserve an IP address (based  
on the WG602v4’s MAC address) on the DHCP server. That way, you can con-  
figure the wireless access point with a static IP address which you can always use  
to log in to make future configuration changes.  
)NSTALLATION 'UIDE  
NETGEAR WG602v4 54 Mbps Wireless Access Point  
Power. The power light should be lit. If the power light is not lit,  
check the connections and to see if the power outlet is controlled by a wall  
switch that is turned off.  
3. TEST WIRELESS CONNECTIVITY  
Start Here  
Using a PC with a wireless adapter configured according to the wireless settings you  
just set in the WG602v4 to establish a wireless connection to the WG602v4.  
Ethernet. The Ethernet (LAN) light on the WG602v4 should be lit  
(amber for a 10 Mbps connection and green for a 100 Mbps connection). If  
not, make sure the Ethernet cable is securely attached at both ends.  
Please refer to the online Reference Manual for instructions on advanced configuration  
options. A link to the NETGEAR WG602v4 54 Mbps Wireless Access Point Reference  
Manual is on the Resource CD.  
Deploy the WG602v4  
Estimated Completion Time: 30 minutes.  
WLAN. The wireless light should be lit.  
Tip: Before mounting the WG602v4 in a high location, first set up and test the WG602v4  
to verify wireless network connectivity.  
Now that you have finished the setup steps, you are ready to deploy the WG602v4 in your  
network. If needed, you can now reconfigure the PC you used in step 1 back to its original  
TCP/IP settings.  
2. CONFIGURE LAN AND WIRELESS ACCESS  
a. Configure the WG602v4 Ethernet port for LAN access. Connect to the  
address field.  
First, Set Up the WG602v4  
1. Disconnect the WG602v4 and position it where you will deploy it. The best location  
is elevated, such as wall mounted or on the top of a cubicle, at the center of your  
wireless coverage area, and within line of sight of all the mobile devices.  
1. CONNECT THE WIRELESS ACCESS POINT TO YOUR COMPUTER AND  
MODEM  
2. Position the antenna. Vertical positioning provides best side-to-side coverage.  
Horizontal positioning provides best top-to-bottom coverage.  
a. Unpack the box and verify the contents.  
3. Connect an Ethernet cable from your WG602v4 Access Point to a LAN port on your  
router, switch, or hub.  
A login window will display.  
b. Prepare a PC with an Ethernet  
adapter. If this PC is already part  
of your network, record its TCP/IP  
b. When prompted, enter admin for the user  
name and password for the password, both  
in lower case letters.  
4. Connect the power adapter to the wireless access point and plug the power adapter in  
to a power outlet. The PWR, LAN, and WLAN lights should light up.  
configuration settings. Configure  
A
the PC with a static IP address of  
192.168.0.210 and 255.255.255.0  
as the Subnet Mask.  
The NETGEAR WG602v4 54 Mbps Wire-  
less Access Point user interface will display.  
ꢀꢀꢀꢀꢀꢀ&DEOH  
Now, Verify Wireless Connectivity  
c. Under Setup on the main menu, select IP  
Settings and configure the IP Settings for  
your network.  
Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity by  
using a browser such as Netscape® or Internet Explorer to connect to the Internet, or  
check for file and printer access on your network.  
c. Connect an Ethernet cable from  
the WG602v4 to the PC (point A).  
B
:*ꢀꢁꢂYꢃ  
d. Securely insert the other end of the  
cable into the WG602v4 Ethernet  
port (point B).  
d. Select Wireless Settings under Setup on the  
&RPSXWHU  
Note: If you cannot connect, see to Troubleshooting Tips in this guide or the online Refer-  
ence Manual. (A link to the Reference Manual is on the Resource CD.)  
main menu and configure the wireless access settings. See the online help or the  
online Reference Manual for full instructions.  
ꢀ(WKHUQHW  
ꢀꢀꢀꢀ3RUW  
e. Connect the Power Adapter from  
the WG602v4 to an AC power  
outlet.  
Note: If you change the default subnet of the LAN IP address, you will be  
disconnected from the WG602v4 Access Point user interface. To reconnect,  
reconfigure your computer with a static IP address within the new LAN IP  
subnet.  
Troubleshooting Tips  
Here are some tips for correcting simple problems you may have.  
Note: Only connect your wireless access point using the power supply provided  
with the WG602v4.  
 

Network Technologies Switch ST xU User Manual
Newcon Optik Binoculars LRB 7X50 User Manual
Nikon Film Camera 1689 User Manual
Nokia Telephone BT DIVERSE 5100 User Manual
Nostalgia Electrics Popcorn Poppers LPM 529 User Manual
Olympus Camera Lens 261055 User Manual
Oster Mixer 2534 User Manual
Palsonic CRT Television 5169 User Manual
Panasonic Computer Monitor BT 4LH310 User Manual
Panasonic Handheld Game System KXL 810A User Manual