NETGEAR Network Router FVS318v3 User Manual

d. Disconnect the cable at the computer end only, point A in the diagram.  
menu, Internet Options, Connections tab page where you can select “Never dial a  
connection.”  
e. Securely insert the Ethernet cable from your modem (Cable 1 in the diagram)  
)NSTALLATION 'UIDE  
FVS318v3 Broadband ProSafe VPN Firewall  
into the INTERNET port of the FVS318v3 as shown in point B of the diagram.  
B
Start Here  
Follow these instructions to set up your VPN firewall. You can also consult the  
PWR  
d. Check the FVS318v3 status lights to verify the following:  
LOCAL Ports  
Test  
Internet  
Reference Manual on the NETGEAR Web site at http://kbserver.netgear.com.  
Prepare to Install Your FVS318v3 VPN  
Firewall  
PWR: The PWR light should turn solid green. If it does not turn solid green,  
check the adapter or the power switch.  
f. Securely insert the blue cable that came with your FVS318v3 (the Blue  
NETGEAR Cable in the diagram below) into a LOCAL port on the firewall such  
as LOCAL port 8 (point C in the diagram), and the other end into the Ethernet  
port of your computer (point D in the diagram).  
TEST: The TEST light goes on when the router is first turned on and then  
goes off. If after two minutes it is still on, see the Troubleshooting Tips in  
this guide.  
For Cable Modem Service: When you perform the VPN firewall setup steps be sure to  
use the computer you used when you first set up your cable Internet connection.  
INTERNET: The INTERNET port LINK light should be lit. If not, make sure  
the Ethernet cable is securely attached to the FVS318v3 Internet port and the  
modem. Also, make sure the modem is powered on.  
For DSL Service: You may need information such as the DSL login name/e-mail  
address and password in order to complete the VPN firewall setup.  
D
LOCAL: A LOCAL LINK/ACT light should be lit. The 100 LED indicates  
your computer is communicating at 100 Mbps; off indicates 10 Mbps. If a  
LOCAL LINK/ACT light is not lit, check that the Ethernet cable from the  
computer to the firewall is securely attached at both ends, and that the  
computer is turned on.  
First, Connect the FVS318v3  
1. CONNECT THE CABLES BETWEEN THE FVS318V3, COMPUTER, AND  
MODEM  
C
a. Turn off your computer.  
Now, Configure the FVS318v3 for Internet  
Access  
b. Unplug and turn off the broadband modem.  
c. Locate the Ethernet cable (Cable 1 in the diagram) that connects your modem  
and computer.  
Your network cables are connected and you are ready to restart your network.  
Use the Smart Wizard configuration assistant to configure the FVS318v3.  
2. RESTART YOUR NETWORK IN THE CORRECT SEQUENCE  
1. From the Ethernet connected computer you just set up, open a browser such as  
Internet Explorer or Netscape® Navigator. With the FVS318v3 in its factory default  
state, your browser will display the NETGEAR Smart Wizard welcome page.  
Warning: Failure to restart your network in the correct sequence could prevent you  
from connecting to the Internet.  
a. First, plug in the power cord to your broadband modem, turn it on, and wait two  
minutes.  
Note: If you do not see this page, type http://www.routerlogin.net in the browser  
address bar and click Enter.  
b. Now, plug in the power cord to your FVS318v3, turn it on, and wait one minute.  
c. Last, turn on your computer.  
A
Note: For DSL customers, if ISP-provided software logs you in to the Internet,  
do not run that software. You may need to go to the Internet Explorer Tools  
 

National Instruments Network Card 5411 User Manual
National Instruments Network Card FP 3000 User Manual
NEC Recording Equipment 760417 User Manual
Niles Audio Speaker CM710FX User Manual
Nokia Stereo Amplifier MA 967 User Manual
NordicTrack Home Gym 307920 User Manual
Nortech Systems Switch RS 232 TERM User Manual
Nostalgia Electrics Frozen Dessert Maker SCM 802 User Manual
Optimus Clock Radio 12 1626 User Manual
Panasonic Car Stereo System CF P2 User Manual